LibreDrive firmware for HL-DT-ST BD-RE BU40N

[mdhankins1]

Hello. I am a little confused about which LibreDrive firmware to pick for this drive. Any help? Using the mk-firmware-pack-20200720.

HL-DT-ST-BD-RE_BU40N-1.04-NM00500-212005061142.bin (BU40N-N-Main)

HL-DT-ST-BD-RE_BU40N-U100-3M01801-211910161036.bin (BU40N-U-Tier2-Non-UHD)

When I view my device in SDFtool Flasher, it shows HL-DT-ST_BD-RE_BU40N_U101_212012011720_MO6L9191353

Thanks

[dcoke22]

The Ultimate UHD Drives Flashing Guide says BU40N on any Firmware directly to > BU40N 1.03MK

[mdhankins1]

When I try the BU40N 1.03MK firmware I get an error message.

Command produced error code 0xff05c103

(nevermind, I tried the following morning and the flash worked)

[Mercutio]

Acutally I am a bit puzzled, too.

I tried to flash my drive, and it looks promising in the first moment:

Code: Select all

PS C:\Program Files (x86)\MakeMKV> .\makemkvcon64.exe f --all-yes -d  E: rawflash -i HL-DT-ST-BD-RE_BU40N-1.03-NM00000-211810241934.bin

Reading input file HL-DT-ST-BD-RE_BU40N-1.03-NM00000-211810241934.bin
Flashing flags = 0x0 : 0 0 0 0 : ---- ---- ---- ----
Current Drive ID: HL-DT-ST_BD-RE_BU40N_1.02_212012011716_MZFO3UD5238
Ready to write drive flash memory. (auto confirmed)
Operation started: Sending flash image to drive
 100% Operation finished
Operation started: Programming flash
 100% Operation finished
Done successfully

But after I restarted the pc and open makeMKV it still states this information:

Code: Select all

Drive Information
OS device name: E:
Manufacturer: HL-DT-ST
Product: BD-RE BU40N
Revision: 1.02
Serial number: [Removed]
Firmware date: 2120-12-01 17:16
Bus encryption flags: 1F
Highest AACS version: 77

LibreDrive Information
Status: Possible (with patched firmware)
Drive platform: MT1959
Harware support: Yes
Firmware support: No
Firmware type: Original (patched version available)
Firmware version: 1.02
DVD all regions: Possible (with patched firmware)
BD raw data read: Possible (with patched firmware)
BD raw metadata read: Possible (with patched firmware)
Unrestricted read speed: Possible (with patched firmware)

Also - I though it might be some drive caching issue - I just gave it a shot. But without luck:

Code: Select all

Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED' occurred while issuing SCSI command AD010..080002400 to device 'SPTI:\Device\CdRom0'
Can't read AACS VID from disc - most likely current AACS host certificate is revoked by your drive
Saved AACS dump file as C:\Users\(...)\(...).tar.gz
LibreDrive compatible drive is required to open this disc - video can't be decrypted.
Failed to open disc

Thanks in advance for any help.

EDIT
I also tried the sdftool_flasher with the FW Versions 1.00 and 1.03 (as recommended)

[d00zah]

HL-DT-ST-BD-RE_BU40N_1.02_212012011716_MO3L91F0715.bin is listed as an encrypted FW in the guide. Either add enc to the command line, or make sure 'Encrypted FW' (?) is a green check in the GUI tool.

[yamslover]

Drive Information
OS device name: /dev/sr0
Manufacturer: HL-DT-ST
Product: BD-RE BU40N
Revision: U100
Serial number: KFNGAJF2958
Firmware date: 2116-08-31 11:53
Bus encryption flags: 1F

LibreDrive Information
Status: Possible, not yet enabled
Drive platform: MT1959

No disc inserted




I am having trouble locating the matching 1.03‑MK for HL-DT-ST_BD-RE_BU40N_U100_211608311153_KFNGAJF2958. Is there any libredrive firmware for this model?

[Billycar11]

Drive Information
OS device name: /dev/sr0
Manufacturer: HL-DT-ST
Product: BD-RE BU40N
Revision: U100
Serial number: KFNGAJF2958
Firmware date: 2116-08-31 11:53
Bus encryption flags: 1F

LibreDrive Information
Status: Possible, not yet enabled
Drive platform: MT1959

No disc inserted




I am having trouble locating the matching 1.03‑MK for HL-DT-ST_BD-RE_BU40N_U100_211608311153_KFNGAJF2958. Is there any libredrive firmware for this model?

see guide below

or email me or marty for an auto flasher but they are windows only the auto flashers

[yamslover]

Thank you I was overthinking it and had the enc command in there rather than main, it appears to be working now with the tutorial.