SDFtool Flasher

Forum for discussions about UHD-capable dives
Coopervid
Posts: 1145
Joined: Tue Feb 19, 2019 10:32 pm

Re: SDFtool Flasher

Post by Coopervid »

dg1218 wrote:
Fri Oct 14, 2022 12:40 pm
I've tried this one first using the new SDFtool Flasher 1.37 and using the old SDFtool Flasher
BP50NB40 to > BP50NB40-NB50-1.03MK then to > BP60NB10 1.02MK

Then I tried both ways
NB52 to > BP50NB40-NB50-1.03MK with enc > BP50NB40-NB50-1.03MK with bootloader/full flash > BP60NB10 1.00_HBD

Each time the flasher says complete no errors, but the firmware version makemkv show never changes. I've also been running the SDFtool Flasher as admin. The drive still reads blueray disk as normal. I've tried about 4 Uhd bluerays with no luck. I got the MK bin files from this link at the beginning of this post. Not really sure what I'm doing incorrectly
Found this in the thread SDFTool flasher:

UPDATE - 21/12/2021:
The latest version of the SDFtool Flasher has a checkbox option to flash the boot loader with the main firmware to the drive. This is useful for the newer BP50NB40 with SVC: NB52. It's also possible that other newer models may require this option later on. We will all work it out together as we go!!

For the moment, to flash the BP50NB40 SVC:NB52, using the latest SDFtool Flasher, follw the steps below:

1. Flash the drive to BP50NB40 (NB50) 1.03-MK.

Now for the crossflash:

3. Select the RECOVERY option and in the pop up, select the BP50NB40 (NB50) 1.03-MK firmware that you just flashed.
4. Select the BP60NB10 1.00-MK firmware in the normal drop box.
5. Click START
Billycar11
Posts: 3766
Joined: Sun Aug 24, 2014 5:49 am

Re: SDFtool Flasher

Post by Billycar11 »

Coopervid wrote:
Fri Oct 14, 2022 1:11 pm
dg1218 wrote:
Fri Oct 14, 2022 12:40 pm
I've tried this one first using the new SDFtool Flasher 1.37 and using the old SDFtool Flasher
BP50NB40 to > BP50NB40-NB50-1.03MK then to > BP60NB10 1.02MK

Then I tried both ways
NB52 to > BP50NB40-NB50-1.03MK with enc > BP50NB40-NB50-1.03MK with bootloader/full flash > BP60NB10 1.00_HBD

Each time the flasher says complete no errors, but the firmware version makemkv show never changes. I've also been running the SDFtool Flasher as admin. The drive still reads blueray disk as normal. I've tried about 4 Uhd bluerays with no luck. I got the MK bin files from this link at the beginning of this post. Not really sure what I'm doing incorrectly
Found this in the thread SDFTool flasher:

UPDATE - 21/12/2021:
The latest version of the SDFtool Flasher has a checkbox option to flash the boot loader with the main firmware to the drive. This is useful for the newer BP50NB40 with SVC: NB52. It's also possible that other newer models may require this option later on. We will all work it out together as we go!!

For the moment, to flash the BP50NB40 SVC:NB52, using the latest SDFtool Flasher, follw the steps below:

1. Flash the drive to BP50NB40 (NB50) 1.03-MK.

Now for the crossflash:

3. Select the RECOVERY option and in the pop up, select the BP50NB40 (NB50) 1.03-MK firmware that you just flashed.
4. Select the BP60NB10 1.00-MK firmware in the normal drop box.
5. Click START
Fyi for everyone it works both ways just a different way of doing it
Buy a UHD drive from the guide and how to video maker: https://www.makemkv.com/forum/viewtopic ... 20&t=17831
UHD Drives Guide: https://www.makemkv.com/forum/viewtopic ... 16&t=19634
Auto flash kit $25 Email me for one Billycar5924@gmail.com
dg1218
Posts: 5
Joined: Fri Oct 14, 2022 1:55 am

Re: SDFtool Flasher

Post by dg1218 »

Coopervid wrote:
Fri Oct 14, 2022 1:11 pm
dg1218 wrote:
Fri Oct 14, 2022 12:40 pm
I've tried this one first using the new SDFtool Flasher 1.37 and using the old SDFtool Flasher
BP50NB40 to > BP50NB40-NB50-1.03MK then to > BP60NB10 1.02MK

Then I tried both ways
NB52 to > BP50NB40-NB50-1.03MK with enc > BP50NB40-NB50-1.03MK with bootloader/full flash > BP60NB10 1.00_HBD

Each time the flasher says complete no errors, but the firmware version makemkv show never changes. I've also been running the SDFtool Flasher as admin. The drive still reads blueray disk as normal. I've tried about 4 Uhd bluerays with no luck. I got the MK bin files from this link at the beginning of this post. Not really sure what I'm doing incorrectly
Found this in the thread SDFTool flasher:

UPDATE - 21/12/2021:
The latest version of the SDFtool Flasher has a checkbox option to flash the boot loader with the main firmware to the drive. This is useful for the newer BP50NB40 with SVC: NB52. It's also possible that other newer models may require this option later on. We will all work it out together as we go!!

For the moment, to flash the BP50NB40 SVC:NB52, using the latest SDFtool Flasher, follw the steps below:

1. Flash the drive to BP50NB40 (NB50) 1.03-MK.

Now for the crossflash:

3. Select the RECOVERY option and in the pop up, select the BP50NB40 (NB50) 1.03-MK firmware that you just flashed.
4. Select the BP60NB10 1.00-MK firmware in the normal drop box.
5. Click START

Just tried that method, same results even with the boot loader option checked.
MartyMcNuts
Posts: 2460
Joined: Wed Nov 22, 2017 11:45 pm

Re: SDFtool Flasher

Post by MartyMcNuts »

dg1218 wrote:
Fri Oct 14, 2022 11:23 pm
Coopervid wrote:
Fri Oct 14, 2022 1:11 pm
dg1218 wrote:
Fri Oct 14, 2022 12:40 pm
I've tried this one first using the new SDFtool Flasher 1.37 and using the old SDFtool Flasher
BP50NB40 to > BP50NB40-NB50-1.03MK then to > BP60NB10 1.02MK

Then I tried both ways
NB52 to > BP50NB40-NB50-1.03MK with enc > BP50NB40-NB50-1.03MK with bootloader/full flash > BP60NB10 1.00_HBD

Each time the flasher says complete no errors, but the firmware version makemkv show never changes. I've also been running the SDFtool Flasher as admin. The drive still reads blueray disk as normal. I've tried about 4 Uhd bluerays with no luck. I got the MK bin files from this link at the beginning of this post. Not really sure what I'm doing incorrectly
Found this in the thread SDFTool flasher:

UPDATE - 21/12/2021:
The latest version of the SDFtool Flasher has a checkbox option to flash the boot loader with the main firmware to the drive. This is useful for the newer BP50NB40 with SVC: NB52. It's also possible that other newer models may require this option later on. We will all work it out together as we go!!

For the moment, to flash the BP50NB40 SVC:NB52, using the latest SDFtool Flasher, follw the steps below:

1. Flash the drive to BP50NB40 (NB50) 1.03-MK.

Now for the crossflash:

3. Select the RECOVERY option and in the pop up, select the BP50NB40 (NB50) 1.03-MK firmware that you just flashed.
4. Select the BP60NB10 1.00-MK firmware in the normal drop box.
5. Click START

Just tried that method, same results even with the boot loader option checked.
Using SDFtool Flasher (v1.3.4 is the latest) perform the following.

1. Flash the drive to BP50NB40 (NB50) 1.03-MK. I SEE YOU HAVE ALREADY DONE THIS STEP!!

Now for the crossflash:

2. Select the RECOVERY option and in the pop up, select the BP50NB40 (NB50) 1.03-MK firmware that you just flashed.
3. Select the BP60NB10 1.00-MK firmware in the normal drop box.
4. Click START

I have never seen this not work and I have done it hundreds of times. There is no need to use the bootloader option.
Cheers :D
----------------------------------------------------------------------------------------------------------------------------
For UHD enabled drives (AU/NZ/SG) & DIY Single Drive Flasher (WW): https://www.uhdenableddrives.com
dg1218
Posts: 5
Joined: Fri Oct 14, 2022 1:55 am

Re: SDFtool Flasher

Post by dg1218 »

MartyMcNuts wrote:
Sat Oct 15, 2022 2:15 am
dg1218 wrote:
Fri Oct 14, 2022 11:23 pm
Coopervid wrote:
Fri Oct 14, 2022 1:11 pm


Found this in the thread SDFTool flasher:

UPDATE - 21/12/2021:
The latest version of the SDFtool Flasher has a checkbox option to flash the boot loader with the main firmware to the drive. This is useful for the newer BP50NB40 with SVC: NB52. It's also possible that other newer models may require this option later on. We will all work it out together as we go!!

For the moment, to flash the BP50NB40 SVC:NB52, using the latest SDFtool Flasher, follw the steps below:

1. Flash the drive to BP50NB40 (NB50) 1.03-MK.

Now for the crossflash:

3. Select the RECOVERY option and in the pop up, select the BP50NB40 (NB50) 1.03-MK firmware that you just flashed.
4. Select the BP60NB10 1.00-MK firmware in the normal drop box.
5. Click START

Just tried that method, same results even with the boot loader option checked.
Using SDFtool Flasher (v1.3.4 is the latest) perform the following.

1. Flash the drive to BP50NB40 (NB50) 1.03-MK. I SEE YOU HAVE ALREADY DONE THIS STEP!!

Now for the crossflash:

2. Select the RECOVERY option and in the pop up, select the BP50NB40 (NB50) 1.03-MK firmware that you just flashed.
3. Select the BP60NB10 1.00-MK firmware in the normal drop box.
4. Click START

I have never seen this not work and I have done it hundreds of times. There is no need to use the bootloader option.
I have done all three of these steps multiple times. The firmware version has not changed. I have tried the BP60NB10 1.02-MK firmware for the last step as well as the BP60NB10 1.00-MK. After I have opened MakeMKV to confirm firmware has changed and it remains on the BP50NB40 (NB50) 1.03 firmware version. I've also tried to read about 4 UHD bluerays, none will open. I have even tried running this on two different computers with the same results. Should the version change show up under the drive info section of MakeMKV after this process is complete?
MartyMcNuts
Posts: 2460
Joined: Wed Nov 22, 2017 11:45 pm

Re: SDFtool Flasher

Post by MartyMcNuts »

dg1218 wrote:
Sat Oct 15, 2022 3:29 am
MartyMcNuts wrote:
Sat Oct 15, 2022 2:15 am
dg1218 wrote:
Fri Oct 14, 2022 11:23 pm



Just tried that method, same results even with the boot loader option checked.
Using SDFtool Flasher (v1.3.4 is the latest) perform the following.

1. Flash the drive to BP50NB40 (NB50) 1.03-MK. I SEE YOU HAVE ALREADY DONE THIS STEP!!

Now for the crossflash:

2. Select the RECOVERY option and in the pop up, select the BP50NB40 (NB50) 1.03-MK firmware that you just flashed.
3. Select the BP60NB10 1.00-MK firmware in the normal drop box.
4. Click START

I have never seen this not work and I have done it hundreds of times. There is no need to use the bootloader option.
I have done all three of these steps multiple times. The firmware version has not changed. I have tried the BP60NB10 1.02-MK firmware for the last step as well as the BP60NB10 1.00-MK. After I have opened MakeMKV to confirm firmware has changed and it remains on the BP50NB40 (NB50) 1.03 firmware version. I've also tried to read about 4 UHD bluerays, none will open. I have even tried running this on two different computers with the same results. Should the version change show up under the drive info section of MakeMKV after this process is complete?
How old is your drive? What is the manufacture date on the drive?
Cheers :D
----------------------------------------------------------------------------------------------------------------------------
For UHD enabled drives (AU/NZ/SG) & DIY Single Drive Flasher (WW): https://www.uhdenableddrives.com
Coopervid
Posts: 1145
Joined: Tue Feb 19, 2019 10:32 pm

Re: SDFtool Flasher

Post by Coopervid »

Please post your Makemkv info. Most importantly it has to have the MT1959 chip.

And a potential issue is the enclosure if you use it via USB. Not all support flashing.

Please provide as much information as possible. Currently it's like pulling teeth....
dg1218
Posts: 5
Joined: Fri Oct 14, 2022 1:55 am

Re: SDFtool Flasher

Post by dg1218 »

The manufacture date on the drive is April 13, 2022. This drive was just purchased a couple of weeks ago. On the enclosure it says Model: BP50NB40 SVC Code: NB52
It is a usb drive and I'm using both the usb data and extra power connection. Voltage Rating is 5V (1.8A). The Rom Ver listed on the drive is 1.03. Below is the Makemkv info. It is the MT1959 chip.

Drive Information
OS device name: D:
Manufacturer: HL-DT-ST
Product: BD-RE BP50NB40
Revision: 1.03
Serial number: SIM2121V95240
Firmware date: 2120-05-07 09:17
Bus encryption flags: 17

LibreDrive Information
Status: Enabled
Drive platform: MT1959
Firmware type: Patched (microcode access re-enabled)
Firmware version: 1.03
DVD all regions: Yes
BD raw data read: Yes
BD raw metadata read: Yes
Unrestricted read speed: Yes
Coopervid
Posts: 1145
Joined: Tue Feb 19, 2019 10:32 pm

Re: SDFtool Flasher

Post by Coopervid »

Everything looks good so far. The only variable is the enclosure. Maybe that's the issue. What model is it?

Do you have a chance to take it out and connect directly to SATA in a desktop PC?
MartyMcNuts
Posts: 2460
Joined: Wed Nov 22, 2017 11:45 pm

Re: SDFtool Flasher

Post by MartyMcNuts »

dg1218 wrote:
Sat Oct 15, 2022 12:48 pm
The manufacture date on the drive is April 13, 2022. This drive was just purchased a couple of weeks ago. On the enclosure it says Model: BP50NB40 SVC Code: NB52
It is a usb drive and I'm using both the usb data and extra power connection. Voltage Rating is 5V (1.8A). The Rom Ver listed on the drive is 1.03. Below is the Makemkv info. It is the MT1959 chip.

Drive Information
OS device name: D:
Manufacturer: HL-DT-ST
Product: BD-RE BP50NB40
Revision: 1.03
Serial number: SIM2121V95240
Firmware date: 2120-05-07 09:17
Bus encryption flags: 17

LibreDrive Information
Status: Enabled
Drive platform: MT1959
Firmware type: Patched (microcode access re-enabled)
Firmware version: 1.03
DVD all regions: Yes
BD raw data read: Yes
BD raw metadata read: Yes
Unrestricted read speed: Yes
When you try the process I mentioned previously, do you get any error codes? Also, when flashing, make sure there is no disc in the drive. You did flash BP50NB40 (NB50) 1.03-MK to it, didn't you?
Cheers :D
----------------------------------------------------------------------------------------------------------------------------
For UHD enabled drives (AU/NZ/SG) & DIY Single Drive Flasher (WW): https://www.uhdenableddrives.com
JediFonger
Posts: 11
Joined: Sat Dec 12, 2020 8:50 am

Re: SDFtool Flasher

Post by JediFonger »

Drive Information
OS device name: A:
Current profile: BD-ROM
Manufacturer: ASUS
Product: BW-16D1HT
Revision: 3.10
Firmware date: 2119-01-04 10:14
Bus encryption flags: 1F
Highest AACS version: 77

LibreDrive Information
Status: Enabled
Drive platform: MT1959
Firmware type: Patched (microcode access re-enabled)

^the Asus ODD flasher.exe worked.

but when i used 1.3.4 GUI of this tool, i checked encrypted and no boot loader and write but it looked like it went through 100% but nothing happened. i rebooted computer still nothing. more of a FYI.
MartyMcNuts
Posts: 2460
Joined: Wed Nov 22, 2017 11:45 pm

Re: SDFtool Flasher

Post by MartyMcNuts »

JediFonger wrote:
Wed Oct 19, 2022 2:40 am
Drive Information
OS device name: A:
Current profile: BD-ROM
Manufacturer: ASUS
Product: BW-16D1HT
Revision: 3.10
Firmware date: 2119-01-04 10:14
Bus encryption flags: 1F
Highest AACS version: 77

LibreDrive Information
Status: Enabled
Drive platform: MT1959
Firmware type: Patched (microcode access re-enabled)

^the Asus ODD flasher.exe worked.

but when i used 1.3.4 GUI of this tool, i checked encrypted and no boot loader and write but it looked like it went through 100% but nothing happened. i rebooted computer still nothing. more of a FYI.
ASus BW-16D1HT 3.10 is not encrypted.
Cheers :D
----------------------------------------------------------------------------------------------------------------------------
For UHD enabled drives (AU/NZ/SG) & DIY Single Drive Flasher (WW): https://www.uhdenableddrives.com
JediFonger
Posts: 11
Joined: Sat Dec 12, 2020 8:50 am

Re: SDFtool Flasher

Post by JediFonger »

could the tool throw that message? i didnt know that
MartyMcNuts
Posts: 2460
Joined: Wed Nov 22, 2017 11:45 pm

Re: SDFtool Flasher

Post by MartyMcNuts »

JediFonger wrote:
Wed Oct 19, 2022 9:25 pm
could the tool throw that message? i didnt know that
No need as SDFtool Flasher already has that fw as not encrypted. You are the one who toggled the encrypted flag when you should have left it alone.
Cheers :D
----------------------------------------------------------------------------------------------------------------------------
For UHD enabled drives (AU/NZ/SG) & DIY Single Drive Flasher (WW): https://www.uhdenableddrives.com
dreadmclaren
Posts: 4
Joined: Tue Nov 01, 2022 7:52 pm

Re: SDFtool Flasher

Post by dreadmclaren »

Code: Select all

Drive Information
OS device name: E:
Manufacturer: HL-DT-ST
Product: BD-RE BP60NB10
Revision: 1.02
Serial number: MD1G3BA3205
Firmware date: 2120-05-07 09:35
Bus encryption flags: 17

LibreDrive Information
Status: Enabled
Drive platform: MT1959
Firmware type: Patched (microcode access re-enabled)
Firmware version: 1.02
DVD all regions: Yes
BD raw data read: Yes
BD raw metadata read: Yes
Unrestricted read speed: Yes
Hello

I crossflashed my BP50NB40 and everything seemed to go smoothly, but now I can't open the drive. The light blinks after sending the 'eject' command and then stops and nothing happens. Original firmware was 1.00 went to BP50NB40-NB50-1.03MK then BP60NB10 1.02MK. Did I miss something?
Post Reply