Page 1 of 2
Fatal error occurred
Posted: Sun Sep 26, 2010 4:35 pm
by tontona
When I launch MakeMKV 1.6.0 it says "Fatal error occurred, program will now exit."
I'm running win7 x64
Re: Fatal error occurred
Posted: Mon Sep 27, 2010 10:48 pm
by beamer234
Hello,
I have the same problem with 1.60 and w7 64bit
To admin:
Why is it not possible to go back to 1.58 (worked fine with w7 64bit), it forces the update to 1.60 and nothing is possible with this version
Re: Fatal error occurred
Posted: Tue Sep 28, 2010 8:04 am
by mike admin
You can still download the old version from videohelp.com and install into another folder.
Re: Fatal error occurred
Posted: Tue Sep 28, 2010 11:02 pm
by beamer234
To admin:
Using version 1.58 is not possible.
After installation / starting the following message is shown:
"This application version is too old.
Please download the latest version at
http://www.makemkv.com"
The program quits ...
best regards
beamer 234
Re: Fatal error occurred
Posted: Wed Sep 29, 2010 3:12 am
by awtlaw
You can download v1.4.4 from video help, but not the previous version (v1.5.
. Anyone know where we can download v1.5.8? I am currently using v1.5.4.
Re: Fatal error occurred
Posted: Wed Sep 29, 2010 4:27 am
by LSUTailg8er
Have been updating MakeMKV for over a year with no problems until this last update and I get the same fatal error message and shut down.
Re: Fatal error occurred
Posted: Thu Sep 30, 2010 6:06 am
by mike admin
beamer234 wrote:To admin:
Using version 1.58 is not possible.
After installation / starting the following message is shown:
"This application version is too old.
Please download the latest version at
http://www.makemkv.com"
The program quits ...
best regards
beamer 234
You can use any old version as long as you enter registration key, either a free beta key or your purchased key.
Could you please check if it's a 64-bit problem? From MakeMKV folder type on command line
Code: Select all
makemkvcon64 info disc:0
makemkvcon info disc:0
and see if program fails in both cases.
Re: Fatal error occurred
Posted: Thu Sep 30, 2010 3:51 pm
by awtlaw
You can use any old version as long as you enter registration key, either a free beta key or your purchased key.
This is incorrect. I have been using version 1.5.4 and once the beta key expired yesterday now it gives us the error that it is too old. Even setting the date back doesn't help because the program just closes out.
Re: Fatal error occurred
Posted: Fri Oct 01, 2010 4:01 am
by LSUTailg8er
bump
hoping some admins can push this issue to the forefront.
Re: Fatal error occurred
Posted: Fri Oct 01, 2010 10:22 pm
by beamer234
To admin:
starting two commands in command line
1. makemkvcon64 info disc:0
a window opens with: "MakeMKV console application funktioniert nicht mehr (... does?nt work any more...)"
2. makemkvcon info disc:0
gives in command line window: Das ?ffnen der Disk schlug fehl (Opening the disk failes...)
windows 7 64bit
Re: Fatal error occurred
Posted: Sat Oct 02, 2010 6:57 am
by mike admin
From the other thread - please try the following - start a command prompt, navigate to the folder where MakeMKV is installed and type
Code: Select all
cmd /c set APROXY_FORCE_32BIT=1 && makemkv
Re: Fatal error occurred
Posted: Sat Oct 02, 2010 8:30 am
by beamer234
Hello,
I?ve tried this:
cmd /c set APROXY_FORCE_32BIT=1 && makemkv
the following happens:
The application window opens, after about 5 sec
it closes with the massage:
"Fehler aufgetreten, Programm wird beendet"
"Error occurred, program will be terminated"
windows 7 64bit
beamer 234
Re: Fatal error occurred
Posted: Tue Oct 05, 2010 7:13 am
by KurtKroemer
Hi everbody,
I do have the same problem.
i'm on a german Win7 64bit Ultimate
When i try "cmd /c set APROXY_FORCE_32BIT=1 && makemkv"
makemkv still starts the x64 realease.
it only works in 32bit mode, when using single steps
cmd
set APROXY_FORCE_32BIT=1
makemkv
cheers
Kurt
Re: Fatal error occurred
Posted: Thu Oct 07, 2010 12:53 am
by nascar
I had the same fatal error with v1.6 on Win7 x64.
After using Kurt's SET suggestion, I was able to launch MakeMKV without the error. I then entered my registration code and re-booted. Now MakeMKV will launch without the fatal error and without having to enter the SET parameter.
Re: Fatal error occurred
Posted: Sun Oct 10, 2010 8:09 am
by mike admin
Please post your EXACT version of win7. Do you have a service pack installed? beta service pack?