www.makemkv.com

It was just a dirty sensor! Guess the hundreds of opening and closing I did over the past couple months added just enough dust to cause the issue.

i have not had any 5.25 pioneers fail other than shipping damage Got the replacement disc, no luck with it. Before I go and buy another drive, is it possible that WP50NB40 (NB52) on BP60NB10 (BP60NB10 1.00_HBD firmware) can't read this newer (made in 2023) UHD disc because of the firmware? Would a ...

i have not had any 5.25 pioneers fail other than shipping damage Got the replacement disc, no luck with it. Before I go and buy another drive, is it possible that WP50NB40 (NB52) on BP60NB10 (BP60NB10 1.00_HBD firmware) can't read this newer (made in 2023) UHD disc because of the firmware? Would a ...

Billycar11 wrote: ↑

Sat Jan 13, 2024 4:51 am

then replace your drive with a pioneer

Do the pioneers have a better design for the ribbon cable where it doesn't break from wearing down because it is folded? I had a different drive do that on me. This isn't exhibiting the failure signs that that one did though.

looks ok post the full error is it keys? read errors? if its read errors clean the disc with a damp microfiber and dry with another. after that replace the disc then if it still dont work clean the lasers in your drive then replace your drive with a pioneer No errors, drive never gets past loading ...

show the drive info did you flash it correctly? I assume so, it has worked for the couple hundred discs I have put in it so far (with at least 10-20 being UHD). Drive Information OS device name: R: Current profile: BD-ROM Manufacturer: HL-DT-ST Product: BD-RE BP60NB10 Revision: 1.00 Serial number: ...

Post the Makemkv error messages. The disc might not yet be supported. If so, send in the .tgz created and in the meantime try this: https://forum.makemkv.com/forum/viewtopic.php?f=12&t=32784 The disc doesn't even load in the OS (Windows 11, and Arch Linux were tested) so there are no MakeMKV er...

I am trying to read Indiana Jones and the Dial of Destiny UHD on my WP50NB40 cross flashed to BP60NB10 v1.00 firmware.
It doesn't open the disc at all.

This is the only UHD disc I have had issues with on this drive, the non-UHD disc version was read fine.

Should I just ask for a replacement disc?

I had the exact same problem It's getting hung up on smaller meaningless titles in handbrake change the minimum title length from 10seconds to 600seconds (10min) it will sail right through it and work again I don't see this option. It also only happens when I start the encode. Edit: Fixed it by man...

Figured the issue out. Looks like the ribbon cable providing power and data is failing. When the tray is open it connects fine and when it is closed it disconnects. Now I will see if I can find a new ribbon cable.

I have a BU40N that was working great for the past few days as I was ripping a UHD box set. I ran into a scratched disc in the set and it seems to have triggered something. After ripping the next UHD blu-ray after skipping the scratched one because it failed to rip, my BU40N basically fails to power...

When I go to create a custom rip with Handbrake using the libmmdb.dll feature I get this crash: Faulting application name: HandBrake.exe, version: 1.6.1.0, time stamp: 0x63558578 Faulting module name: libmmbd.dll, version: 1.6.0.0, time stamp: 0x60e60963 Exception code: 0xc0000005 Fault offset: 0x00...

Coopervid wrote: ↑

Thu Feb 11, 2021 9:53 am

This adapter only provides power to the drive and has no data connection to your computer.

Yup and I plugged in the SATA data cable. Thought that was obvious based on the behavior I described.

I bought a HLDS BU40N and have been using it in the Vantec enclosure, recently the drive stopped showing up in the enclosure. To test if it was the enclosure vs the drive I bought a slimline adapter (Amazon - CRJ SATA Power 15-Pin Male to SATA 6-Pin Slimline Sleeved Power Adapter Cable) so I can plu...

I get a similar error and I went and ripped the drive instead of backup and found that it is a specific title which it skips: Error when saving: DEBUG: Code 0 at *0,;c\PL0:J=9lq%:213140472 DEBUG: Code 0 at "YUaD@ooUA^hBfH;-:121263613 DEBUG: Code 0 at Vh_?F0ugBjm==LP;:29406166 DEBUG: Code 0 at V...